This High Output Ignition Coil is an inductive smart coil capable of producing extremely high spark energy making it ideal for many high horsepower applications, particularly those running high boost, high rpm, high compression, or nitrous injected applications. The coil near plug form factor allows it to be mounted on the valve cover(s) or remotely mounted away from the cylinder head to promote lower operating temperatures of the coil, improving longevity and performance. This coil is suited for a wide variety of applications, ranging from daily driven applications through 3500+ horsepower blown alcohol motors. It is the ideal combination of high spark energy and long spark duration.

Since it's a smart coil with a 19 amp IGBT ignitor built in that can be driven with a 5 volt logic level output, no external ignitor is required. When installing these high output coils, high quality wiring and proper wiring logic is required to handle the massive output of these coils. The center pin must be grounded to the cylinder head. The coil will not supply full power if it is not grounded to the cylinder head. The coil will overheat if operated at excessive duty cycles for prolonged periods. Do not operate this coil at a duty cycle greater than 40%.

These coils each deliver over 100mJ of spark energy and a minimum of 40,000 Volts which is as much as most CDI type systems without the need for a CDI module. However, they provide this high output in conjunction with a very long spark duration at full energy, unlike CDI systems and multiple spark systems which fire off small spark events before & after the main burst of spark.

The IGN-1A coils are shock and weatherproof allowing them to be mounted wherever you prefer. These coils cost less than aftermarket LS coils and deliver enhanced performance and were designed for a mass production application where reliability is paramount. 

Features:
CDI-like spark energy without the need for a CDI
Less expensive than aftermarket LS1 coils
Robust construction allows them to be mounted almost anywhere
Massive Spark Energy, up to 103 mJ
Up to 40kV Output Voltage, without a CDI
Incredibly long spark duration, up to 2.9mS
Can be mounted directly to the engine

Specifications:
Output (no load): 40kV minimum
Output (50pF load): 40kV +/- 10%
Output Energy: 103 mJ +/- 7%
Peak Secondary Current: 102 mA +/- 10%
Arc Duration: 2.9mS +/- 10%
Turns Ratio 71:1
Maximum Current: 19 Amps
Maximum Battery Voltage: 17 Volts
Base Dwell: 3.0 mS
Max Continuous Dwell: 9 mS but don’t exceed 40% duty cycle
Max Intermittent Dwell: 80% duty cycle, 5 seconds maximum
Mating Connector: Packard/Delphi 12162825 “Pull to Seat” (Available separately as connector & contacts or as crimped pigtail)
Mating Contacts: Packard/Delphi 12124075 “Pull to Seat”
High Tension Wire Terminal: HEI “Spark Plug Top” Style Plug Wire Ends

These are universal coils that work with almost all aftermarket ECU's, not just our own ECU's. These are the same coils offered at a higher price by AEM, Holley, DIY, AMP, etc. 

Connection:
A: Coil Trigger (ECU Trigger)
B: Coil Trigger (ECU 0V)
C: GND to Cyl Head
D: Battery GND
E: Battery POS

Price is per coil. 

Write a review

Please login or register to review

IGN-1A Smart Coil | Coil On Plug | Coil Near Plug

  • $79.99
  • $69.99


Available Options


Related Products

PiMPxs Standalone Engine Management (Sequential EFI)

PiMPxs Standalone Engine Management (Sequential EFI)

-For Factory Equipped Sequential EFI Applications (86-95 V8 Mustangs, 94-95 Mass-Air V8 F-Series/Bro..

$995.99 $1,099.99

Microsquirt Plug & Play Standalone Engine Management + Harness | 2.3L | Entry Level

Microsquirt Plug & Play Standalone Engine Management + Harness | 2.3L | Entry Level

Microsquirt is an entry-level ECU designed to control a wide array of applications. In this applicat..

$659.99 $739.99

PiMPx | PiMPxs | PiMPxshift Expansion Port Pigtail Harness

PiMPx | PiMPxs | PiMPxshift Expansion Port Pigtail Harness

The expansion port allows for options not supported by the factory harness such as sequential spark ..

$79.99

PiMPxshift Standalone Powertrain Management with Transmission Control (Sequential or Batch EFI)

PiMPxshift Standalone Powertrain Management with Transmission Control (Sequential or Batch EFI)

-For Factory Equipped Pre-OBD2 EFI Applications with AOD-E, 4R70W, or E4OD Transmission (F-Series, S..

$1,399.99 $1,529.99

Coil Near Plug Expansion Harness | For LS Coils or IGN-1A Coils | V8 | PiMPx | PiMPxs | PiMPxshift

Coil Near Plug Expansion Harness | For LS Coils or IGN-1A Coils | V8 | PiMPx | PiMPxs | PiMPxshift

This expansion harness plugs into the ECU's expansion port, through the firewall, and to the engine...

$304.99 $329.99

CAS & Expansion Coil/Ignition Harness Kit | 4 Cyl | PiMPx | PiMPxs

CAS & Expansion Coil/Ignition Harness Kit | 4 Cyl | PiMPx | PiMPxs

Includes both our CAS (cam angle sensor) that bolts to the stock distributor as well as the expansio..

$569.99 $589.99

Cam Angle Sensor | CAS | TFI Distributor Conversion Kit

Cam Angle Sensor | CAS | TFI Distributor Conversion Kit

This kit is designed to work with Ford TFI distributors and PiMP, PiMPx, PiMPxs, PiMPxshift, Megasqu..

$299.99 $329.99

Coil Brackets | IGN-1A Smart Coils | Remote Mount | Billet Aluminum

Coil Brackets | IGN-1A Smart Coils | Remote Mount | Billet Aluminum

These brackets can be used to mount our IGN-1A Smart Coils (also sold by Holley, AEM, AMP EFI, etc.)..

$59.99 $49.99

Wiring | IGN-1A Smart Coil | Connector | Pigtail | 48"

Wiring | IGN-1A Smart Coil | Connector | Pigtail | 48"

This pigtail harness plugs into the IGN-1A coils (Stinger Performance, DIY, Holley, AEM, etc.) and a..

$13.99

Coil Near Plug Expansion Harness | For LS Coils or IGN-1A Coils | 4 Cyl | PiMPx | PiMPxs

Coil Near Plug Expansion Harness | For LS Coils or IGN-1A Coils | 4 Cyl | PiMPx | PiMPxs

This expansion harness plugs into the ECU's expansion port, through the firewall, and to the engine...

$274.99 $289.99

CAS & Expansion Coil/Ignition Harness Kit | V8 | PiMPx | PiMPxs | PiMPxshift

CAS & Expansion Coil/Ignition Harness Kit | V8 | PiMPx | PiMPxs | PiMPxshift

Includes both our CAS (cam angle sensor) that bolts to the stock distributor as well as the expansio..

$599.99 $625.99

CAS + Expansion Coil/Ignition Harness Kit + IGN-1A Coils | 4 Cyl | PiMPx | PiMPxs

CAS + Expansion Coil/Ignition Harness Kit + IGN-1A Coils | 4 Cyl | PiMPx | PiMPxs

Includes both our CAS (cam angle sensor) that bolts to the stock distributor as well as the expansio..

$859.99 $899.99

CAS + Expansion Coil/Ignition Harness Kit + IGN-1A Coils | V8 | PiMPx | PiMPxs | PiMPxshift

CAS + Expansion Coil/Ignition Harness Kit + IGN-1A Coils | V8 | PiMPx | PiMPxs | PiMPxshift

Includes both our CAS (cam angle sensor) that bolts to the stock distributor as well as the expansio..

$1,169.99 $1,259.99

IGN-1A Smart Coil Crimp Connector With Pins

IGN-1A Smart Coil Crimp Connector With Pins

This connector plugs into the IGN-1A coils and allows you to crimp the included pins directly to you..

$5.29

PiMPxs Engine Management + CAS + COP Kit | Sequential EFI | V8

PiMPxs Engine Management + CAS + COP Kit | Sequential EFI | V8

-For Factory Equipped Sequential EFI Applications (86-95 Mustangs, 94-95 Mass-Air F-Series/Bronco) ..

$2,019.99 $2,229.99

PiMPxshift w/ Transmission Control  + CAS + COP Kit | Sequential or Batch EFI | V8

PiMPxshift w/ Transmission Control + CAS + COP Kit | Sequential or Batch EFI | V8

-For Factory Equipped Sequential or Batch Fire EFI Applications with E4OD or 4R70W Transmission (86-..

$2,499.99 $2,699.99

PiMPxs Engine Management + CAS + COP Kit | Sequential EFI | 4 Cyl

PiMPxs Engine Management + CAS + COP Kit | Sequential EFI | 4 Cyl

For Factory 4 Cylinder Batch Fire Applications that want to convert to Sequential EFI (Inj..

$1,749.99 $1,829.99

Microsquirt Plug & Play Standalone | 2.3L Ford | Harness Only

Microsquirt Plug & Play Standalone | 2.3L Ford | Harness Only

This is for people who purchased a Microsquirt ECU before they were aware of our plug and play kit a..

$334.99 $349.99

Separators | Spark Plug Wire | Clamp Style | Aluminum | 8-10mm

Separators | Spark Plug Wire | Clamp Style | Aluminum | 8-10mm

Billet Aluminum anodized spark plug wire separators for 8mm, 9mm, and 10mm wires. These clean up the..

$9.99 $12.99

Tags: ign-1a, ign1a, coil, coils, smart, ignition, coil on plug, holley, aem, haltec, motec, FAST, AMP, AMPefi, DIY, small, big, block, coil near plug, sbf, bbf, 302, 351, 460, 347, 427, 428, 429, 300, V8, I6, 4 cylinder, 2.3, 2.5, 2.0, LSx, LS1, LS2, LS3, honda, mazda, toyota, supra, rx7, miata, mustang, camaro, corvette, 2jz